收藏本站
71M6543F/71M6543G Data Sheet
registers LCD_MAPn (0x2405 – 0x240B) . Setting the bit corresponding to the pin in LCD_MAPn to 1
configures the pin for LCD, setting LCD_MAPn to 0 configures it for DIO.
After reset or power up, pins SEGDIO0 through SEGDIO15 are initially DIO outputs, but are
disabled by PORT_E = 0 (I/O RAM 0x270C[5] ) to avoid unwanted pulses during reset. After
configuring pins SEGDIO0 through SEGDIO15 the MPU must enable these pins by setting
PORT_E .
Once a pin is configured as DIO, it can be configured independently as an input or output. For SEGDIO0
to SEGDIO15, this is done with the SFR registers P0 (SFR 0x80) , P1 (SFR 0x90) , P2 (SFR 0xA0) and P3
(SFR 0xB0) , as shown in Table 47 .
Example: SEGDIO12 (pin 32 in Table 47 ) is configured as a DIO output pin with a value of 1 (high) by
writing 0 to bit 4 of LCD_MAP[15:8] , and writing 1 to both P3[4]and P3[0] . The same pin is configured
as an LCD driver by writing 1 to bit 4 of LCD_MAP[15:8] . The display information is written to bits 0 to 5
of LCD_SEG12.
The PB pin is a dedicated digital input and is not part of the SEGDIO system.
The CE features pulse counting registers and each pulse counter interrupt output is internally
routed to the pulse interrupt logic. Thus, no routing of pulse signals to external pins is required in
order to generate pulse interrupts. See interrupt source No. 2 in Figure 12 .
A 3-bit configuration word, I/O RAM register DIO_Rn ( I/O RAM 0x2009[2:0] through 0x200E[6:4] ) can be
used for pins SEGDIO2 through SEGDIO11 (when configured as DIO) and PB to individually assign an
internal resource such as an interrupt or a timer control ( DIO_RPB[2:0], I/O RAM 0x2450[2:0], configures
the PB pin). This way, DIO pins can be tracked even if they are configured as outputs. Table 47 lists the
internal resources which can be assigned using DIO_R2[2:0] through DIO_R11[2:0] and DIO_RPB[2:0] . If
more than one input is connected to the same resource, the resources are combined using a logical OR.
Table 46: Selectable Resources using the DIO_Rn[2:0] Bits
Value in DIO_Rn[2:0]
0
1
2
3
4
5
Resource Selected for SEGDIOn or PB Pin
None
Reserved
T0 (counter0 clock)
T1 (counter1 clock)
High priority I/O interrupt (INT0)
Low priority I/O interrupt (INT1)
Note:
Resources are selectable only on SEGDIO2 through SEGDIO11 and the
PB pin. See Table 48 .
When driving LEDs, relay coils etc., the DIO pins should sink the current into GNDD (as
shown in Figure 16, right), not source it from V3P3D (as shown in Figure 16 , left). This is due
to the resistance of the internal switch that connects V3P3D to either V3P3SYS or VBAT. See
6.4.6 V3P3D Switch on page 136 .
Sourcing current in or out of DIO pins other than those dedicated for wake functions, for
example with pullup or pulldown resistors, must be avoided. Violating this rule leads to
increased quiescent current in sleep and LCD modes.
58
v2
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
71M6545-IGT/F IC ENERGY METERING
720-10007-00300 CBL D-SUB 9PIN FMAL-25PIN FML 3M
720-10010-00025 CBL DSUB 9PIN FML-25PIN MAL .25M
720-10020-00300 CBL DSUB 9PIN FML-9PIN MALE 3M
720-10021-00300 CBL DSUB 9PIN FML-9PIN FEMAL 3M
72231-0881 8 POS T/P SHLD 4 GR ASSY
7250B PANEL KIT BOTTOM FOR R-1220 CASE
731-10061-00200 CBL DSUB HD 15FEMAL-15MALE 2.0M
相关代理商/技术参数
71M6543F-IGTR/F 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6543FT-IGT/F 制造商:Maxim Integrated Products 功能描述:ENERGY METER ICS - Rail/Tube
71M6543FT-IGTR/F 制造商:Maxim Integrated Products 功能描述:3-PHASE SOC, 64KB FLASH, PRES TEMP SENSOR - Tape and Reel
71M6543G 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Selectable Gain of 1 or 8 for One Current Energy Meter ICs Metrology Compensation
71M6543GH 制造商:未知厂家 制造商全称:未知厂家 功能描述:电表IC
71M6543GHT-IGT/F 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KB, PRES TEMP SENSOR, HI PREC - Bulk
71M6543GHT-IGTR/F 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KB, PRES TEMP SENSOR, HI PREC - Tape and Reel
71M6543G-IGT/F 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel